Keep these important operating instructions. Check www.meyersound.com for updates.OPERATING INSTRUCTIONS500-HP Compact High-Power Subwoofer
CHAPTER 1: INTRODUCTION10
11CHAPTER 2: POWER REQUIREMENTSThe 500-HP subwoofer combines advanced loudspeaker technology with equally advanced power capabilities. Understanding p
CHAPTER 2: POWER REQUIREMENTS12The AC Loop Output Connector (Gray)The gray AC Loop Output connector allows multiple 500-HP subwoofers to be looped and
500-HP OPERATING INSTRUCTIONS13CAUTION: The power source for the 500-HP should always operate within the required volt-age range, at least a few volts
CHAPTER 2: POWER REQUIREMENTS14NOTE: For best performance, the AC cable voltage drop should not exceed 10 V, or 10 percent at 115 V and 5 percent at 2
15CHAPTER 3: AMPLIFICATION AND AUDIOThe low-frequency drivers in the 500-HP are powered by a two-channel proprietary Meyer Sound amplifier with MOSFET
CHAPTER 3: AMPLIFICATION AND AUDIO16Loop Output ConnectorThe male XLR Loop connector allows multiple 500-HP sub-woofers to be looped from a single aud
500-HP OPERATING INSTRUCTIONS17On/Temp LEDWhen the 500-HP is powered on, its On/Temp LED turns green. If the temperature of the heatsink reaches 85° C
CHAPTER 3: AMPLIFICATION AND AUDIO18AMPLIFIER COOLING SYSTEMThe amplifier for the 500-HP uses natural convection for cooling at low to moderate audio
19CHAPTER 4: INTEGRATING 500-HP SUBWOOFERSINTEGRATING 500-HP SUBWOOFERS WITH MEYER SOUND LOUDSPEAKER SYSTEMSIt is often necessary to augment mid-high
iiDECLARATION OF CONFORMITY ACCORDING TO ISO/IEC GUIDE 22 AND EN 45014Manufacturer’s Name:Meyer Sound Laboratories Inc.Manufacturer’s Address:2832 San
CHAPTER 4: INTEGRATING 500-HP SUBWOOFERS20Placement for 500-HP SubwoofersAn important factor governing subwoofer response is their placement relative
500-HP OPERATING INSTRUCTIONS21measurement system like Meyer Sound’s SIM 3 is rec-ommended to determine appropriate delay and polarity settings.DIGITA
CHAPTER 4: INTEGRATING 500-HP SUBWOOFERS22
23CHAPTER 5: QUICKFLY RIGGING500-HP subwoofers equipped with the optional MRF-500 rigging frame can be linked directly to the MG-M’elodie multipurpose
CHAPTER 5: QUICKFLY RIGGING24GuideALinks are easily set to one of three positions (A, B, or C) with accessible knobs. GuideALink labels indicate the p
500-HP OPERATING INSTRUCTIONS25Groundstacking 500-HPs with M’elodiesA maximum of five M’elodies can be groundstacked above a single 500-HP. When groun
CHAPTER 5: QUICKFLY RIGGING26CAUTION: When securing GuideALinks to the MG-M’elodie grid, make sure to use the quick-release pins with the red or blue
500-HP OPERATING INSTRUCTIONS27Adjusting the Angle for MG-M’elodie Grid and 500-HP ConfigurationsWhen the MG-M’elodie’s front and rear GuideALinks are
CHAPTER 5: QUICKFLY RIGGING28more information, see “MG-M’elodie Grid Load Rat-ings” on page 26 and “500-HP Load Ratings” on page 30.500-HP with Flown
500-HP OPERATING INSTRUCTIONS29500-HPs with Flown M’elodies500-HPs can be flown within M’elodie arrays to supplement and extend low-frequency headroom
iiiSYMBOLS USEDThese symbols indicate important safety or operating features in this booklet and on the chassis:IMPORTANT SAFETY INSTRUCTIONS1. Read t
CHAPTER 5: QUICKFLY RIGGING30500-HP Load RatingsTable 9 lists the maximum number of M’elodies that can be safely suspended from a 500-HP. For MG-M’elo
500-HP OPERATING INSTRUCTIONS31Safety Guidelines for Using the MCF-500 Caster Frame Do not stack more than three 500-HPs. When transporting stacks,
CHAPTER 5: QUICKFLY RIGGING32
33CHAPTER 6: THE RMS REMOTE MONITORING SYSTEMAn optional RMS remote monitoring system module can be installed in the 500-HP, allowing it to be connect
CHAPTER 6: THE RMS REMOTE MONITORING SYSTEM34The RMS software displays all loudspeakers on the network in a panel with icons, Meter views, and Text vi
500-HP OPERATING INSTRUCTIONS35Reset ButtonPressing the Reset button causes the RMS module’s firm-ware to reboot; this will not affect whether the lou
CHAPTER 6: THE RMS REMOTE MONITORING SYSTEM36
37CHAPTER 7: SYSTEM DESIGN AND INTEGRATION TOOLSMeyer Sound offers two comprehensive tools to assist with the acoustical and functional requirements o
CHAPTER 7: SYSTEM DESIGN AND INTEGRATION TOOLS38Using MAPP Online ProMAPP Online Pro is compatible with the following operating systems: Windows Lin
39APPENDIX A: OPTIONAL VEAM MULTIPIN CONNECTORThe 500-HP subwoofer requires a grounded outlet. It is very important that the system be properly ground
ivSAFETY SUMMARYEnglish To reduce the risk of electric shock, dis-connect the loudspeaker from the AC mains before installing audio cable. Reconnect
APPENDIX A: OPTIONAL VEAM MULTIPIN CONNECTOR40
41APPENDIX B: OPTIONAL RAIN HOODWeather-protected versions of the 500-HP subwoofer are available with rain hood kits that safeguard the subwoofer’s el
APPENDIX B: OPTIONAL RAIN HOOD423. Attach the user panel rain hood assembly to the user panel, slipping it under the flange at the top of the panel an
43APPENDIX C: SPECIFICATIONS500-HP COMPACT HIGH-POWER SUBWOOFER SPECIFICATIONS500-HP SpecificationsACOUSTICALOperating Frequency Range35 Hz – 140 HzNo
APPENDIX C: SPECIFICATIONS44AMPLIFIERType Two-channel complementary MOSFET output stages (class AB/H)Output Power 1800 W total (2 x 900 W)Note: Wattag
500-HP OPERATING INSTRUCTIONS45500-HP Dimensions15.45 [392 mm]18.23 [463 mm]18.00 [457 mm]26.55 [674 mm]22.50 [572 mm]22.18 [563 mm]Ø1.52 [Ø39 mm]8.50
APPENDIX C: SPECIFICATIONS46MCF-500 CASTER FRAME SPECIFICATIONSMCF-500 SpecificationsPHYSICALMaterials and ComponentsPremium birch plywood base with
Meyer Sound Laboratories Inc. 2832 San Pablo Avenue Berkeley, CA 94702www.meyersound.com T: +1 510 486.1166 F: +1 510 486.835© 2009Meyer Sound. All ri
vCONTENTSChapter 1: Introduction 7How to Use This Manual 7Introducing the 500-HP Subwoofer 7Chapter 2: Power Requirements 11AC Power Distribution 11Th
CONTENTSvi
7CHAPTER 1: INTRODUCTIONHOW TO USE THIS MANUALMake sure to read these operating instructions in their entirety before configuring a loudspeaker system
CHAPTER 1: INTRODUCTION8allows the subwoofer to be easily paired with UltraSeries™ loudspeakers. Also included with all 500-HPs are durable plastic bo
500-HP OPERATING INSTRUCTIONS9500-HP Groundstacked with M’elodiesMG-M’elodie Grid with 500-HP and M’elodie Array
Comments to this Manuals