Meyer-sound UPA-2P User Manual download pdf (Page 2)

AC Input

100-240V

50-60Hz 4A MAX

24VFan

Loop

Input

On / Temp.

Limit

Earth /

Chassis

Case

220k Ω

GND Circuit

Looping Audio Input

Push

Network

Service

Wink

Reset

Activity

Remote Monitor System

Meyer Sound, Berkeley, CA. USA

CAUTION: See instruction manual

ATTENTION

: Voir le cahier d'instruction

Acoustical

(each loudspeaker)

Coverage

Crossover

Transducers

Standard Audio

Input Module*

Amplifiers

AC Power

Physical

Notes

PHYSICAL DIMENSIONS

UPA-1P & 2P SPECIFICATIONS

Operating Frequency Range

Free Field

Half-Space

Phase Response

Maximum SPL

UPA-1P (-6 dB points)

UPA-2P (-6 dB points)

UPA-1P

UPA-2P

Low Frequency

High Frequency

Type

Connector

Impedance

XLR Wiring

RF Filter

Common Mode Rejection Ratio

Type

Burst capability

THD, IM, TIM

Connector

Automatic voltage selection

Idle RMS Current

Max Continuous RMS Current (

>10 sec)

Max Burst RMS Current (<1 sec)

Max Peak Current During Burst

Soft-Current Turn-on

Dimensions

Weight

Enclosure

Finish

Protective Grill

Rigging

60 Hz - 18 kHz

100 Hz - 16 kHz ± 3dB; -6 dB at 77 Hz and 18 kHz

77 Hz - 16 kHz ± 3dB; -6 dB at 66 Hz and 18 kHz

± 35° 600 Hz - 16 kHz; + 90° at 250 Hz

133 dB SPL

100° H; 40° V

45° H; 45° V

1200 Hz

1000 Hz

12" cone driver

3" diaphragm compression driver

Differential balanced input circuit

Female XLR; male XLR loop

10 kΩ differential balanced (between pins 2 and 3)

Pin 1: chassis; Pin 2: + signal; Pin 3: - signal

Common Mode: 425 kHz low-pass; Differential Mode: 142 kHz low-pass

> 80 dB (50 Hz - 1 kHz); typically 90 dB

Complementary power MOSFET output stages (class AB/bridged)

350 Wrms/channel

< .02 %

PowerCon locking AC connector

80-264 VAC continuous; 47/63 Hz

@115 V: 0.25Arms @230V: 0.13Arms @100V: 0.3Arms

@115 V: 2.8Arms @230V: 1.4Arms @100V: 3.2Arms

@115 V: 3.2Arms @230V: 1.6Arms @100V: 3.7Arms

@115 V: 5.0Apk @230V: 2.5Apk @100V: 5.8Apk

Inrush current <15A@115V

14.5" W x 22.4" H x 14.5" D

77 lbs (35 kg)

” plywood

Black textured

Hex perforated steel grill, charcoal grey foam

Four aircraft pan fittings (two on top, two on bottom). Working load

is 600 lb (273 kg), based on a 5:1 safety factor.

1. Measurements are taken at 3m on-axis,

/3 octave, unless otherwise stated.

2. Response depends on loading conditions and room acoustics.

3. Measured with a single boundary, 1 m from rear of cabinet.

4. Phase variation from pure delay.

5. Measured at 1 m, with pink noise or music.

6. Nominal 8Ω resistive load, pink noise, 100v peak.

* Refer to UPA series Q+A for input module options.

ALL UNITS IN INCHES

Meyer Sound Laboratories, Inc.

2832 San Pablo Avenue

Berkeley, CA 94702

tel: 510.486.1166

fax: 510.486.8356

e-mail: [email protected]

http://www.meyersound.com

®®

LISTED

3K59

COMMERCIAL

AUDIO SYSTEM

Meyer Sound Laboratories

has devoted itself to

designing, manufacturing,

and refining components

that deliver superb sonic

reproduction. Every part of

every component is

designed and built to

exacting specifications

and undergoes rigorous,

comprehensive testing

in the laboratories.

Research remains an

integral, driving force

behind all production.

Meyer strives for sound

quality that is predictable

and neutral over an

extended lifetime and

across an extended range.

Made by Meyer Sound, Berkeley, CA, USA

European Office:

Meyer Sound Germany

GmbH

Carl Zeiss Strasse 13

56751 Polch, Germany

UPA1P&2P - 04.054.017.01D

14.3

30°

14.5

12.8

7.7

2.6

7.5

22.4